Do US injection molders have a minimum order? What 873 molder websites say
Few US injection molders publish a minimum order quantity (MOQ). On November 10, 2026, we read the websites of 873 US injection molders: about 9 in 10 (90%) say nothing about order size, so you have to ask. Only 39 (4%) give a lowest quantity, most often 100 parts a run, and 25 (3%) say they have no minimum.
Most of those 39 numbers are the bottom of a range a shop says it can cover, such as 100 to 100,000 parts; only 14 are worded as a minimum. None of them tells you the price. Where sites give times, the median stated build time is about 2.5 to 4 weeks for an aluminum or prototype mold (12 sites) and about 6 to 9 weeks for a steel production mold (10 sites), and a production order of parts takes about 2 to 4 weeks (27 sites). The most common quote promise is 24 hours (8 of 17 sites that state one). Treat every "stated" count in this post as a floor, since a site can say more on a page we didn't read.
For a first run of a few hundred to a few thousand parts, the minimums that are printed are low: of the 15 sites that give a lowest quantity per run or per order, 14 put it at 500 parts or fewer. Those are shops advertising small runs, so they say little about the nine in ten that print nothing. Websites rarely mention what decides the job: setup charges on short runs, the mold's cost spread over your units, and whether the shop plans around yearly volumes far above yours.
How do US molder websites state a minimum order?
We sorted the 873 readable websites by the clearest thing each one says about order size, counting each website once.
| What the site says about order size | Sites | Share of 873 |
|---|---|---|
| A lowest quantity as a number (a stated minimum, or the bottom of a stated range) | 39 | 4.5% |
| No minimum, or no job too small | 25 | 2.9% |
| Low volume or short runs, with no number | 10 | 1.1% |
| A typical or ideal range only | 10 | 1.1% |
| The minimum varies or depends on the job, with no number | 7 | 0.8% |
| Nothing about order size | 782 | 89.6% |
Shares are rounded. In all, 91 sites (10.4%) say something about order size.
- A lowest quantity. Of the 39 sites, 14 word it as a minimum, with words such as "minimum," "as few as" or "min." The other 25 give the bottom of a range. Where the number is per run or per order, the median is 100 parts (15 sites, from 1 to 1,000). Six sites give a yearly figure instead, with a median of 10,000 parts a year (6 sites, from 10 to 25,000); five of them are the bottom of a range. Sixteen don't say whether their number is per run or per year; their median is also 100 (16 sites, from 1 to a million). Four sites give 1 as their lowest quantity; they're here because they print a number, and sites that only say they'll run anything from one part up are under no minimum. One sets a minimum order value of $2,500 instead of a quantity, and one high-volume molder asks for at least a million parts.
- No minimum. Of the 25 sites, 14 use the words "no minimum" or "no MOQ." The other 11 say no job is too small, or that they'll run anything from a single part up.
- Low volume, no number. Ten sites talk about low-volume or short-run work without a figure; two of them add that their minimum is flexible.
- A typical range only. Ten sites describe the work they usually take, from small runs up to programs of 100,000 parts or more a year. A high typical range works like a soft minimum.
- It depends. Seven sites say only that the minimum varies or depends on the job.
- Nothing. The 782 sites in the last row say nothing about order size. A shop that says nothing may still have a minimum; you find out by asking.
Why do molders set minimums, and why do so few publish one?
Every run on an injection molding press carries costs that don't depend on its length. The mold has to be hung in the press, the barrel heated and purged of the last job's plastic, the settings dialed in and the first parts checked, and afterward the mold comes out again. Plastic is bought by the bag or box, and a custom color is mixed in batches. A molder's working minimum is a run long enough to pay for all that, and it changes with the part, the press, the plastic, the color and how full the schedule is. That is probably one reason so few sites print a number: any single figure would be wrong for most parts.
Many molders also think in yearly volume, often called estimated annual usage (EAU), because molds, press time and plastic purchases are planned around a year of demand. That's why quote forms ask for annual quantities. Only six sites print a yearly figure, from 10 to 25,000 parts a year, and five of those are the low end of a range.
How long do US molders say molds, parts and quotes take?
Only 77 sites (8.8%) give any time at all, and each kind of time below is stated by fewer than 4% of sites. Where a site gives a range, we took medians of the low ends and the high ends separately. All figures are as stated on November 10, 2026.
- Building an aluminum or prototype mold: 12 sites; median about 2.5 to 4 weeks.
- Building a steel or production mold: 10 sites; median about 6 to 9 weeks.
- Building a mold, kind not stated: 19 sites, with figures from about 1.5 to 18 weeks. In all, 32 sites (3.7%) state a mold build time; some give more than one kind.
- First parts or samples: 19 sites (2.2%), counted from different starting points. Counted from the order (15 sites), most figures fall within about one to four weeks, and a few run 5 to 12 weeks. Counted from a finished mold (4 sites), three give one to three days.
- A production order of parts: 27 sites (3.1%); median 2 to 4 weeks, with stated figures from 2 days to 8 weeks.
- A new project, from start to production parts: 6 sites; about 6 to 20 weeks.
- A quote: 17 sites (1.9%). Eight promise one within 24 hours, 13 of the 17 within two business days, and the slowest say five days to two weeks.
Read these as the fast end: many are worded "as little as" or "as fast as," and a website isn't always updated when the shop gets busy. They fit the ranges in Aluminum or steel injection molds for a first production run. The quote times are for molded parts. A full quote for a product with molds, boards and assembly takes longer; Most factories say they're at capacity puts it at two to four weeks as a rough rule.
What else do molder websites say about small runs, prototype molds and medical work?
For five simpler questions, a script flagged sites by keyword, then an AI model checked 20 flagged sites at random for each flag (the method is under "How did we count?"). The shares below are corrected for the flags that turned out wrong.
- Low-volume or short-run work: about 25% of sites (17% to 32%). The keywords alone flagged 39%, but only 13 of the 20 checked were right; the misses were blog articles, figures of speech, and other processes such as machining or vacuum forming.
- Aluminum, prototype or rapid-tooling molds: about 21% (15% to 23%).
- ISO 13485 certification: 13.6% (10.9% to 14.2%; 19 of the 20 checked were right, which puts the estimate near the top). ISO 13485 is the quality-management standard for medical devices, and since February 2, 2026 the FDA's quality rule for device makers has incorporated it by reference. That rule doesn't apply to makers of components, so whether a molder needs ISO 13485 is up to the device maker buying its parts.
- A clean room: about 14% (11% to 15%). Clean rooms are classed by the concentration of airborne particles under ISO 14644-1; molded parts need one mostly for medical and optical work.
- Startups, inventors or entrepreneurs: about 11% (7% to 14%).
About 1 in 4 sites mention low-volume work and 1 in 5 mention aluminum or prototype molds, many times the 4% that print a lowest quantity. For a few hundred parts, ask those shops first.
Who owns the mold, according to molder websites?
Only 21 sites (2.4%) mention mold ownership at all. Ten say the customer owns the mold, and none says the molder does. The other 11 mention customer-owned molds without stating a rule for new ones: they store and maintain them, take them in from other molders, or leave ownership to the project agreement.
Two of the ten add conditions. One says the mold becomes the customer's once it is paid in full, and that the shop can hold a mold until an unpaid bill is settled (often called a molder's lien). Another says a mold the customer paid for is generally the customer's, but that this can change when the mold's cost is folded into the part price or the shop provides the mold at no charge.
Some states give molders that lien by law. Florida's lets a molder that hasn't been paid for parts it made with a customer's mold keep the mold and, if the bill is still unpaid 60 days after a written notice, sell it at public auction after a second notice giving 30 days, unless the amount owed or the parts' quality is in good-faith dispute. Ask which state's law applies, and keep your contact details with the shop current.
With almost every site silent, ownership gets settled in the quote and the purchase order. Get in writing who owns the mold, when ownership passes, where it's kept, who pays for upkeep and repairs, and whether the molder will release it on request. An ODM quoted a 2,000-unit MOQ, but we need 500 covers the same questions for a whole product.
How did we count?
- Who counted. Anamor's team ran this count from public web pages; we contacted no one.
- The sample. We started from a list of 1,230 US moldmakers and molders that we built from public directories in October and November 2026, and kept the 922 entries that mold parts in the US, prototype molders included. Shops that only build molds and companies that mold overseas were left out. Directories favor shops that market themselves online, so the sample leans toward molders a founder would find by searching.
- What we read. On November 10, 2026, a script read each site's home page and up to eight more relevant pages on the same site, such as capabilities, FAQ, low-volume, prototype, tooling, quote and about pages, skipping any page the site's robots.txt file asks crawlers to leave alone.
- The denominator. Four pairs of entries share a website, so the 922 entries are 918 websites, each counted once. Of those, 873 gave at least 500 characters of readable text; every share in this post is out of those 873, and the other 45 couldn't be read.
- Coding. Text patterns pulled sentences that mention minimums, quantities, lead times, quotes and mold ownership. An AI model read the matching passages from 222 sites and coded them against written rules (order size, the lowest quantity per run or per year, and any times).
- Statements the patterns missed. Patterns miss wording such as a line saying the shop takes runs of any size, or a table that says "Min 1." A wider keyword scan of the other 651 readable sites found 29 more with clear statements, coded the same way and included in every count above.
- Checking the quotes. A script confirmed that each of the 380 coded statements appears word for word on the saved copy of its page. That shows no quote was invented, though not that every code is right.
- The keyword shares. For the five flags in the section on small runs and medical work, an AI model checked 20 flagged sites per flag, picked at random, against their saved pages. The share shown is the flagged share times the share that checked out, and the range is the 95% confidence interval of that check. We didn't measure how many sites the keywords missed.
What the numbers can't tell you:
- They're floors. A site may say more on a page we didn't read, in a PDF or behind a quote form.
- Lead times run on different clocks. Some start at the order, some at approved CAD, some at a finished mold, so treat the medians as rough.
- A site can disagree with itself. One lists a yearly minimum on one page and says in its FAQ that it has no set minimum; another gives a different minimum on each process page. Both are counted under the lowest quantity they state for injection molding.
- A website isn't a quote. It shows what a shop wants to be known for, and its quote for your part can differ in either direction.
What do the numbers mean for a run of a few hundred to a few thousand?
- Don't screen molders by what their websites say about minimums. Nine in ten say nothing, and most printed numbers are the bottom of a range. Ask every shop that fits your part and process.
- Give your yearly volume as well as your first run. Printed per-run floors are low (14 of 15 at 500 parts or fewer) but come from shops that advertise small runs. Only six sites print a yearly figure, too few to measure; quote forms still ask for one, and a shop built around much larger programs may turn you down on it.
- A shop with no minimum still charges for setup. Even a 100-part run means paying for the mold and for setting up the press, and on a short run setup can be a large share of the part price. That's why some shops add a setup charge below a set quantity or ask for a minimum order value. Compare quotes on the cost of your whole run: the mold, plus the part price times your quantity, plus any setup charges. Every $10,000 of mold adds $20 to each part at 500.
- Plan time from the medians, then add margin. Add up an aluminum mold (median about 2.5 to 4 weeks, 12 sites), a round or two of samples (our assumption: one to three weeks for checking parts and adjusting the mold, where sites give only the one to three days to shoot them) and a production order (median about 2 to 4 weeks, 27 sites), and a first run comes to roughly 6 to 11 weeks from the mold order if nothing changes. With a steel mold (median about 6 to 9 weeks, 10 sites) it's about 9 to 16 weeks. The six sites that give a time from project start to production say about 6 to 20 weeks.
- Quotes are quick; finding shops that answer is slow. Most sites that state it promise a part quote within two business days (13 of 17), but the rule of thumb in Most factories say they're at capacity is two real quotes from ten cold contacts.
How do you ask a molder about minimums and lead times?
- Send what a molder needs to quote. STEP files for each part, the plastic and color, the finish, the quantity for the first run and per year, and when you need parts. More in What should you send a manufacturer for a quote.
- Ask about the minimum both ways. Is there a minimum order quantity or a minimum order value per run, and is there a setup charge below some quantity?
- Ask for prices at two or three quantities, such as your first run, twice that, and your yearly volume, with the mold on its own line. What's actually in a production quote explains how to compare them.
- Ask what the mold is. Aluminum or steel, how many cavities, which SPI mold class (101 to 105) the quote assumes, as explained in Aluminum or steel injection molds for a first production run, and how many shots the molder will stand behind in writing.
- Ask for each time and where it starts. Mold build from the order or from approved CAD, first samples, how many sample rounds the price includes, and the lead time for later orders.
- Ask who owns the mold, when ownership passes, where it's kept and whether it will be released on request.
- Ask what a firm quote needs and how long it takes once they have it.
- If the answer is no, ask who might say yes. A molder that turns you down often knows which shops nearby take small runs.
Example: emailing molders for a 500-unit two-part enclosure
This is an illustration, not a customer project. The product is made up, and so are the numbers, except the website figures taken from our count above.
In this made-up case, a founder has a wall-mounted air sensor whose enclosure is two molded parts in black ABS, a base and a cover. She plans a made-up first run of 500 units and, if it sells, a made-up 2,000 a year after that. She wants molded parts within a made-up 10 weeks of ordering the molds.
Setting expectations from the count. Since 9 in 10 molder websites say nothing about order size, she doesn't drop a shop for silence. She lists a made-up 12 molders whose sites mention low-volume work or aluminum molds (about 1 in 4 and 1 in 5 of all sites in the count do). By the website medians, an aluminum mold, samples and a production order can fit her made-up 10 weeks, and a steel mold (median 6 to 9 weeks to build, 10 sites) probably can't, so she asks for aluminum and lets shops offer steel as an option.
The email. Each shop gets one short message with STEP files for both parts, the plastic, color and texture, both made-up quantities, and the questions from the list above, including prices at a made-up 500 and 1,000 sets with the molds listed separately.
The replies. In made-up numbers, 5 of the 12 shops reply within a week and 3 send prices. Of the two that decline, one has a made-up minimum of 5,000 parts a run that its website never mentions, and the other plans around yearly volumes of 50,000 parts or more; both name another shop to try. The made-up quotes:
- Molder A, no minimum (made-up numbers): two aluminum molds at $6,000 each, parts at $2.20 a set, and a $250 setup charge on any run under 1,000 sets. Made-up times: molds in 3 weeks, samples a week later, production 2 weeks after approval. Five hundred sets cost a made-up $13,350, about $26.70 a set.
- Molder B, minimum of 250 sets a run (made-up numbers): one aluminum family mold that makes both parts in each shot at $8,000, and parts at $2.60 a set. Made-up times: mold in 4 weeks, samples 1 to 2 weeks, production 2 weeks. Five hundred sets cost a made-up $9,300, about $18.60 a set.
- Molder C, steel (made-up numbers): two steel molds at $22,000 in all and parts at $1.30 a set, with molds in 8 weeks. Five hundred sets cost a made-up $22,650, about $45.30 a set.
What she decides. In this made-up case, the shop with no minimum comes second on cost, and molder B's minimum of 250 sets doesn't get in the way of 500. B's family mold ties both parts to one plastic and color, which is fine because both are black ABS. It also stops both parts when either needs a change, which matters less here because she can't sell a base without a cover; Can you put several different parts in one injection mold? covers the tradeoff. Over a made-up 2,500 sets, the first run plus a year, B is still cheapest at about $14,500 against about $25,250 for C, whose lower part price only catches up after about 10,800 sets. B's 7 to 8 weeks from order to parts fits her made-up 10 weeks. Before ordering, she asks B how many shots the aluminum mold will stand behind, since a made-up 2,000 sets a year could wear it out within a few years, and she gets mold ownership in writing.
More generally, ask every molder that fits the part, give your yearly volume along with your first run, and compare quotes on the cost of the whole run with the mold included.
Where we come in
If you're sending your first parts to molders and getting silence, or minimums that don't fit your run, this is one of the situations Anamor takes on. We start from your target unit cost and quantity, and our quotes list setup costs, such as tooling and fixtures, separately from unit prices at the quantities you're planning.
Anamor takes US hardware teams with a working prototype into their first production run: we redesign the product for production, line up partner factories and suppliers in the US and overseas, price it at your quantities, and run the build through to shipping.
Send what you have: photos of the prototype, CAD if you have it, any molder quotes or minimums you've already been given, and how many you plan to make, now and over the next year. Need an NDA? We'll send our mutual NDA, or review yours, before you send files. Within two business days, a real person on our team will reply with a free first look at your production run and a few times to talk.
Frequently asked questions
Do US injection molders have a minimum order quantity?
Most don't say. In a November 2026 count by Anamor, 90% of 873 US injection molder websites said nothing about order size. Only 39 (4%) gave a lowest quantity, most often 100 parts a run, and 25 (3%) said they have no minimum. Ask each molder for its minimum quantity, minimum order value and setup charges.
How long does an injection mold take to build in the US?
Among the few US molder websites that state it (12 for aluminum, 10 for steel), the median as of November 2026 is 2.5 to 4 weeks for an aluminum or prototype mold and 6 to 9 weeks for a steel production mold. A production order's median is 2 to 4 weeks (27 sites). Treat these as the fast end.
Does "no minimum order" mean a small injection molding run is cheap?
No. A molder with no minimum still charges for the mold and for setting up the press, and some add a setup charge on short runs or set a minimum order value instead. Compare quotes on the cost of the whole run: the mold, plus the part price times your quantity, plus any setup charges.