Can you put several different parts in one injection mold (a family mold) to cut tooling cost?
Often, yes. A family mold makes several different parts in one shot, like both halves of a case, and usually costs less than a separate mold for each part; one quick-turn molder puts the saving at up to 40% of costs. It fits best for parts in one plastic and color, close in size and needed in equal numbers.
The saving comes from sharing one mold base and one setup per production run and, at high volume, one press cycle for the whole set. The parts are molded together, so each shot waits for the slowest part, every part gets the same plastic and color, the parts come out in fixed numbers, and a fix to one part stops them all. For a run of a few hundred to a few thousand sets, get quotes both ways. The published figures and limits below are as of November 2026.
What is a family mold, and how is it different from a multi-cavity mold?
An injection mold is a block of metal with a hollow in the shape of the part, the cavity. Melted plastic flows from the press through a channel called the runner, enters each cavity through a small opening called the gate, cools, and is pushed out. One cycle is one shot. If you've built a plastic model kit, you've handled a family mold's output: the parts come still attached to the runner, each a different shape, all molded together.
The table compares four ways to tool a product with more than one molded part.
| Mold type | What one shot makes | Tooling cost for a two-part set | Can one part run alone? | Fits |
|---|---|---|---|---|
| A single-cavity mold for each part | One part | Two complete molds | Yes; each mold runs on its own | Parts that differ in size, plastic, color or quantity, and designs still changing |
| Multi-cavity mold | Two or more copies of the same part | A larger mold for each part, with less press time per part | Yes | One part needed in large numbers; rarely pays at a few thousand parts |
| Family mold | One of each different part, a set | One mold: usually less than two separate molds, more than either one alone | Only if the mold is built for it: runner shutoffs (cold runner), or nozzles or valve gates that shut one at a time (hot runner) | Parts used together one-to-one, in one plastic and color, close in size and wall thickness |
| Interchangeable inserts in a standard frame, often called by one maker's trade name, MUD (master unit die) | One part per insert; a two-insert frame can run both parts in one shot | The inserts, often in a frame the molder already owns; one mold maker puts it at 15 to 30% more than a family mold | Yes; each insert can run alone or as a pair | Parts that need different settings, colors or quantities, or may change on their own |
A multi-cavity mold repeats one cavity to make more of one part per shot, and extra cavities rarely pay off at a few thousand parts.
In an interchangeable-insert system, a standard mold base stays in the press while part-specific inserts are swapped in minutes. A two-insert frame runs both parts together like a family mold, and either insert can also run alone. A mold maker that sells both family molds and insert systems puts this route at typically 15 to 30% more up front than a comparable family mold. Some quick-turn services build their molds as inserts for their own frames, so ask who owns the frame and whether your inserts could run anywhere else.
How much does a family mold save, and where does the saving come from?
The published figures all come from companies that sell molds. One quick-turn molder says up to 40% of costs, adding that it won't quite be two for the price of one. A mold maker that sells both family molds and insert systems says 25 to 40% for parts of similar wall thickness and volume, and another mold maker says 40 to 60% less than separate molds for a three-part assembly. Treat these as a range to test against your own quotes.
The saving comes from these places:
- The mold. One base, one set of plates and one build instead of two. Each cavity still has to be cut, so the more complex the cavities, the smaller the share you save.
- Setup. Each production run needs the mold mounted, heated and dialed in, and the first parts checked: once for a family mold, once per mold otherwise.
- Press time. One cycle makes the whole set, which roughly halves press hours for a two-part set. This is where the big savings in published examples come from, and it only adds up at volume.
A 1998 trade-magazine comparison of a two-part ABS set at 50,000 sets a year shows where the saving comes from. The two parts were far apart in size: their own molds ran on 50- and 120-ton presses. A family mold cost about 13% less than the two single-cavity molds, $28,440 against $32,590 in 1998 dollars, but it was run one cavity at a time, so it saved nothing: mold plus press time came to about $135,000 either way. The version with a hot runner, which filled both cavities evenly enough to shoot them together, cost $38,410 in 1998 dollars, about 18% more than the two separate molds, and took two weeks longer to build. Shooting both parts at once halved the press hours, so that version still cut the total by about a quarter. (The article partly promotes a balancing product.)
At a few hundred sets, press time is small: even 20 extra seconds a shot over 500 shots is under three hours. So for a first run, the saving is mostly the mold price and one setup instead of two, and the things to check are whether both parts can be molded well with one set of settings, and what happens when one of them changes.
A family mold also needs a bigger press, which usually costs more per hour. The press is sized for the projected area of all the parts plus the cold runner (the solid plastic left in the channel); a common starting point is 3 tons per square inch, within a range of 2 to 10. In the 1998 example, shooting both parts together took a 170-ton press.
What are the limits and disadvantages of a family mold?
Size and volume. Parts of different size fill at different rates. One quick-turn molder publishes a strict rule for its family molds: two parts may differ in volume by up to 20% for parts under about 33 cm³, 15% from 33 to 82 cm³, 10% from 82 to 164 cm³ and 5% above that, with the same percentages, on bands of their own, for surface area. Mold makers that build custom tools allow far more: one suggests up to 3:1 in volume between the largest and smallest cavity, and the other says 5:1 or more stays a problem however the runners are tuned. Both can be right. A quick-turn shop builds aluminum molds in standard frames with cold runners and little tuning per job, so it needs parts that nearly match; a custom mold maker can size each runner, simulate the fill and, at extra cost, add valve gates.
Fill balance. Plastic takes the easiest path, so the smaller cavity fills first and keeps being packed. In a materials engineer's box-and-lid example, the overpacked lid showed flash (thin fins of plastic at the mold's seams) and a different gloss, and shrank less than the box, so its screw holes might not line up. A smaller runner to the lid let both fill together; shrinking a part's gate to slow it down, the article warns, causes differences in packing, shrinkage and looks.
One plastic, one color. Every cavity gets the same shot, so a clear window, a soft-touch button or a part in an accent color needs its own mold. The upside is a matched set. One molder of cosmetic nylon parts for a premium optical-goods brand chose a family mold for color consistency, spent three to six months adjusting its first one before the parts were acceptable, and later gave each cavity its own electric valve gate. Those were cosmetic parts made to a premium brand's color standard; ask your molder how close your own parts come to that.
The slowest part sets the cycle. In one mold maker's example, a housing needs 25 seconds of cooling and a clip 10, so the clip waits 15 extra seconds every cycle. Walls of different thickness also shrink differently; a mold maker that sells both family molds and insert systems suggests keeping family parts' walls within 0.5 mm of each other.
Fixed quantities. Each shot makes one set. A product that needs two of one part can use one bottom and two tops in the same mold if size and shape allow. But if one part scraps more often than the other, or you need spares of one, every extra shot makes extras of the rest, unless a cavity can be shut off.
One fix stops every part. Metal work on one cavity takes the whole mold out of the press, and supply of every part in it stops. Cavities built as replaceable inserts make the fix quicker. Afterward the process is re-set, so expect new samples of every part in the mold, including the ones that didn't change.
Tolerances. Uneven packing changes how much each part shrinks, so tight-tolerance and highly cosmetic parts are the hardest to put in a family. One mold maker suggests family molds for tolerances of ±0.10 mm or looser.
Can you shut off a cavity and mold only the parts you need?
Yes, if the mold is built for it, usually with a runner shutoff (also called a runner turn-off, or RTO) on each cavity. A runner shutoff is a small rotating insert in the runner; one mold-component catalog describes cylinders that a technician turns 90 or 180 degrees with a rod to block or open the flow to one or more cavities. The closed cavity stays empty while the others run: tops only, for spares, or a damaged cavity blocked until the mold can be repaired. The part is cheap; most of the cost is design time, so ask for it when you order the mold.
Shutting off a cavity changes the process. The open cavities now take the whole shot, so the shot size, packing pressure and hold time have to be re-set and the first parts checked again. One mold maker notes that most quality systems treat each combination of open cavities as its own process, approved separately. Expect a setup charge each time you switch, and ask whether the mold can run with one side empty without flashing, since with one of two cavities shut, the plastic's pressure pushes on one side of the mold only.
With interchangeable inserts, the molder simply runs one insert alone. On a hot runner (heated channels that keep the plastic melted all the way to each part), a cavity can stay closed by switching off the heat to its nozzle so the plastic there freezes, or by keeping its valve gate shut, as long as each valve has its own actuator; valves moved together by one plate can't close one cavity alone.
What is sequential valve gating, and do you need it?
At a few hundred to a few thousand sets, a family mold probably doesn't need sequential valve gating. A valve gate is a pin at a hot runner's gate that opens and closes to let plastic in. Sequential valve gating opens the gates one after another, the largest cavity first, so every cavity finishes filling at about the same moment. In a conference paper from a process-control company, a family mold's center cavity was about three times the volume of each side cavity. Its gate opened at the start of injection, the side gates once 16 and 19 cm³ of plastic had gone in, and all three cavities filled at nearly the same time.
Sequential valve gating costs real money. One mold maker adds $3,000 to $8,000 per extra valve gate, and in the 1998 trade-magazine comparison, a hot runner added about $10,000 in 1998 dollars and two weeks to the mold. Hot runners also make color changes harder. Quick-turn family molds use cold runners, and one quick-turn molder says pin and hot-tip gates are rarely if ever used on its family molds. If two parts need valve sequencing to mold well together, at these quantities they usually belong in separate molds.
When does a family mold fit a run of a few hundred to a few thousand?
At these quantities the mold is the largest one-time cost and a longer cycle adds little. Mold makers' guides suggest family molds below about 10,000 parts a year or 25,000 units a year, and separate single-cavity molds above about 100,000 units a year.
A family mold fits when:
- the parts are used together one-to-one, such as the top and bottom of a case, or a frame and its cover;
- they're the same plastic, grade and color, and matching them is a plus;
- they're close in volume, surface area and wall thickness, inside the limit your molder works to;
- the parts and runner fit the shop's standard mold size; one quick-turn molder lists about 305 × 102 mm or 203 × 152 mm for a whole family, which a larger case's two halves can outgrow;
- the design is settled, or the parts are likely to change together;
- the mold is aluminum and its runners start small, so the molder can open one up cheaply if the balance is off, and its shot life is no limit at these quantities.
Separate molds or inserts fit better when:
- one part is much larger or thicker than the other, such as a housing and a small button;
- the parts need different plastics or colors, such as a clear lens or a soft-touch grip;
- you need different or changing numbers of each, or spares of one;
- one part is still likely to change while the other is settled;
- one part needs side actions (moving pieces of the mold that form side holes and clips) or tight tolerances the other doesn't.
There are other ways to need fewer molds. One design guide suggests designing two halves as the same part, with matching features placed symmetrically, so one mold makes both. Spending less on molds also makes a small first run easier to justify, the problem behind An ODM quoted a 2,000-unit MOQ, but we need 500. Below a few hundred units, a mold may not pay at all; see 100 to 1,000 units: bridge tooling, urethane casting or machining?
Example: a two-part enclosure, two molds or one
This is an illustration, not a customer project. The product is made up, and so are the numbers; only the published size limits described above are real.
In this made-up case, a team needs 500 sets of a handheld device's case, a top and a bottom, both in black PC/ABS. The top is a made-up 50 cm³ with 2.0 mm walls, and the bottom a made-up 53 cm³ with 2.2 mm walls. These made-up halves are about 6% apart in volume, inside the quick-turn molder's 15% limit for parts from 33 to 82 cm³, and a made-up 3% apart in surface area. With a made-up 4% extra for setup and scrap, each mold makes 520 shots.
- Option A, two aluminum molds (made-up numbers): $8,000 for the top mold and $8,500 for the bottom, $16,500; a setup for each at $400 apiece; and about $480 of press time on a 50-ton press at $55 an hour, with 28- and 32-second cycles. Made-up total: about $17,800.
- Option B, one aluminum family mold (made-up numbers): $11,500 for the mold; one setup at $400; and about $300 of press time on a 100-ton press at $65 an hour, with a 32-second cycle set by the thicker bottom. Made-up total: $12,200.
With these made-up numbers, the family mold costs about $5,600 less for the first 500 sets, and $5,000 of that is the mold. The longer cycle and the bigger press barely show, since press time stays under $500 either way in this made-up case.
Now suppose, in this made-up case, the first units show that the USB-C notch in the bottom's edge has to move 3 mm. The notch is open at the seam where the mold halves meet, so it needs no side action. Forming it in its new place means adding metal to the mold, since an opening in the part is solid metal in the mold, and on aluminum that usually means a new insert for the bottom cavity.
- Option A (made-up numbers): a new bottom insert at $3,000 and three weeks, plus new samples of the bottom only at $300; the top mold isn't touched. Made-up cost of the fix: $3,300.
- Option B (made-up numbers): the same insert at $3,000, re-setting the process and checking the fill on the changed cavity at $500, and new samples of both parts at $500, since both come out of the re-set process; neither half can be molded during the made-up three weeks. Made-up cost of the fix: $4,000.
After the fix, the made-up family mold is still about $4,900 ahead, $16,200 against about $21,100. The stoppage also costs less than it sounds: tops can't ship without bottoms, so with separate molds the product waits for the new bottom insert just the same. It would hurt more if the top were also sold as a spare or used in a second product.
A change that pulls the halves apart would erase the saving. If, in this made-up case, the bottom grew to 70 cm³ to fit a bigger battery, it would be 40% larger than the top, far outside the quick-turn molder's 15% limit, though a custom mold maker might still balance it with runner sizing or valve gates at extra cost. The family mold could need a rebuild, or a separate bottom mold with the old bottom cavity shut off for good. Runner shutoffs on both cavities, ordered with the mold for a made-up $400 in all, trim the first-run saving to about $5,200, keep that way out open and let the molder run tops alone for spares. So this made-up team picks the family mold, with a shutoff on each cavity.
More generally, at a few hundred to a few thousand sets, a family mold usually wins on price when the parts match in plastic, color, size and quantity, because the mold is most of the one-time cost and press time is small. It loses when the parts differ enough that one set of settings can't mold both well, or when one part keeps changing on its own.
What should you ask a molder when comparing a family-mold quote with separate molds?
- The price both ways, and for inserts in a standard frame if offered: each with its piece price, setup charge per run and lead time.
- How far apart your parts are in volume, surface area and wall thickness, and whether that's inside the limit the shop works to.
- How the fill will be balanced, whether a fill simulation is in the quote, and who pays to rebalance if the first shots come out uneven.
- Whether each cavity can have a runner shutoff, what it adds, and what each switch costs in setup and first-part checks.
- If one part needs a change, whether its cavity is a replaceable insert, and whether both parts need new samples afterward.
- What cycle time, press size, tolerances and gloss the shop expects for each part in the family mold, compared with a mold of its own.
- If you need the parts in a ratio other than one-to-one, how the cavities will be laid out.
- Who owns the mold, or the inserts and the frame, how many shots it's good for, and whether another molder could run it.
For choosing the metal, see Aluminum or steel injection molds for a first production run; for the design changes molding needs, Moving from a 3D-printed prototype to injection molding; and for the plastic, Which plastic is best for an electronics enclosure.
Where we come in
If your product has two or more molded parts and you're weighing one mold against several, this is one of the situations Anamor takes on. We start from your target unit cost and quantity, design each part for the process that will make it, and list setup costs, such as tooling and fixtures, separately from unit prices at the quantities you're planning.
Anamor takes US hardware teams with a working prototype into their first production run: we redesign the product for production, line up partner factories and suppliers in the US and overseas, price it at your quantities, and run the build through to shipping.
Send what you have: photos of the prototype, CAD if you have it, the plastic and color of each part, and how many you plan to make. Need an NDA? We'll send our mutual NDA, or review yours, before you send files. Within two business days, a real person on our team will reply with a free first look at your production run and a few times to talk.
Frequently asked questions
What is a family mold in injection molding?
A family mold is one injection mold with cavities for several different parts, so each shot makes a set, such as the top and bottom of a case. A multi-cavity mold, by contrast, makes several copies of one part. Family molds suit parts in the same plastic and color, close in size, and needed in equal numbers.
How much does a family mold save compared with separate molds?
Published figures, all from companies that sell molds, run about 25 to 40% less tooling for two similar parts and up to 60% for a three-part assembly; one quick-turn molder says up to 40% of costs. A 1998 trade-magazine comparison found a family mold only about 13% cheaper than two molds. Test these against your own quotes.
Can you run only one part in a family mold?
Yes, if the mold is built for it. On a cold runner, a runner shutoff, a small rotating insert, blocks plastic from reaching one cavity; on a hot runner, that cavity's nozzle or valve gate is shut. The molder then re-sets shot size and packing pressure and checks the first parts again, so expect a setup charge per switch.